The Foundation of Plumbing Knowledge When Installing a Bathtub

Estimate Free

We have discovered this article about A Step-by-Step Guide to Installing a Bathtub down the page on the internet and accepted it made sense to write about it with you here.


Installing A Bathtub
Mounting a tub isn't exactly rocket science, but it does call for solid plumbing, woodworking, and in some cases, tiling skills. Changing an old bath tub with a brand-new one is additionally a moderately hard job. If the old tub is easily easily accessible, the job can relocate speedily; if you have to open a wall to eliminate the old bathtub and also place the brand-new bath tub, the task is a lot harder. In either case, the task is within a residence handyman's skills, although you will require an assistant to vacate the old bathtub and set in the brand-new one. Ensure you have actually qualified on your own for the work as well as fit attempting it. Rather than working with a specialist to take over a halfway-completed project, it is far better to consider using one prior to you begin. Opportunities are you may require a specialist plumber to make tube connections.
This write-up will help you set up a new tub in your restroom if you have currently acquired a brand-new tub and also do not require to transform the arrangement of your previous water pipes.
Your devices and product list ought to consist of the following:
  • New Bathtub

  • Hammer

  • Pipe Wrenches

  • Prybar

  • Shatterproof glass

  • Degree

  • Pliers

  • Adjustable Wrench

  • Putty Blade

  • Screwdriver

  • Cold Knife

  • Tape Measure

  • Pipe Caps


  • Removing Old Touches


    If you need to change old taps with new ones as a part of your setup, then the first thing you need to do is disconnect the water system. After doing so, turn on the faucets to drain any kind of water remaining in the system. The process of removing the existing taps can be fairly troublesome as a result of the restricted accessibility that is typically the case.
    Use a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipelines to the taps. Have a towel prepared for the remaining water that will originate from the pipelines. Once the supply pipelines have been removed, make use of the same tool to loosen up the nut that holds the taps onto the bath/basin. You will need to stop the single taps from transforming throughout this procedure. Once the taps have been removed, the holes in the bath/basin will certainly have to be cleaned of any old securing compound.
    Before moving on to fit the new taps, contrast the pipeline connections on the old faucets to the brand-new taps. If the old taps are longer than the brand-new taps, after that a shank adapter is needed for the brand-new faucets to fit.

    Suitable New Touches


    If the tails of the brand-new taps are plastic, then you will certainly require a plastic connector to avoid damage to the string. One end of the port fits on the plastic tail of the faucet as well as the other end provides a link to the existing supply pipes.
    If you require to fit a monobloc, after that you will call for lowering couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipe.
    Next, position the faucet in the installing opening in the bath/basin making certain that the washers remain in location in between the tap and also the sink. Protect the tap in position with the maker provided backnut. When the faucet is securely in place, the supply pipes can be attached to the tails of the taps. The faucets can either be connected by using corrugated copper piping or with normal faucet ports. The former type needs to be attached to the tap ends initially, tightening up only by hand. The supply pipelines can later be connected to the various other end. Tighten both ends with a spanner after both ends have actually been linked.

    Setting up the Bath tub


    Making use of both wood boards under its feet, position the tub in the required position. The wood boards are handy in uniformly spreading out the weight of the bathtub over the location of the boards rather than concentrating all the weight onto four little factors.
    The next objective is to ensure that the bath tub is leveled all round. This can be achieved by checking the spirit level and also readjusting the feet on the bathtub until the level reads level.
    To set up faucets, fit the bottom of the furthest flexible tap connector to the suitable supply pipeline by making a compression join; then do the very same for the other tap.
    Activate the water and also examine all joints and also new pipework for leakages and tighten them if required. Fill the tub and also examine the overflow electrical outlet as well as the normal electrical outlet for leakages.
    Lastly, repair the bath paneling as defined in the producer's instruction manual. Tiling and also securing around the bathtub must wait until the bathtub has actually been used at the very least once as this will settle it right into its last setting.

    Preparing for the Installment


    First of all, the supporting structure supplied with the bathroom should be fitted (if needed) according to the producer's directions. Next off, fit the taps or mixer to the bath tub. When suitable the tap block, it is important to see to it that if the tap includes a plastic washer, it is fitted between the bathroom and the faucets. On a plastic bathroom, it is likewise practical to fit a sustaining plate under the taps system to avoid strain on the bathtub.
    Fit the adaptable faucet ports to the bottom of the two taps making use of 2 nuts and also olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet with the hole in the bath. Make use of the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
    Next off, fit the end of the adaptable overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bathroom. See to it you utilize every one of the provided washing machines.
    Attach the catch to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a similar manner.The bath should currently be ready to be fitted in its final setting.

    Tiling Around the Tub


    In the area where the bathroom fulfills the floor tile, it is needed to seal the joins with a silicone rubber caulking. This is very important as the installation can move enough to break a rigid seal, causing the water to pass through the wall surface in between the bathroom and the tiling, leading to complications with wetness as well as possible leakages to the ceiling listed below.
    You can pick from a selection of coloured sealers to blend in your components and installations. They are offered in tubes and cartridges, and also are capable of securing spaces approximately a size of 3mm (1/8 inch). If you have a bigger space to fill up, you can fill it with spins of drenched newspaper or soft rope. Remember to constantly load the tub with water prior to securing, to permit the movement experienced when the bathtub is in use. The sealer can break rather early if you do not take into account this motion prior to securing.
    Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are likewise quickly offered on the marketplace. It is suggested to fit the floor tiles using waterproof or water-proof glue and grout.

    Bathtub Installation


    How Important Is A Bathtub To Your Home?


    High-quality baths, showers, and other bathroom updates are necessary when considering a smart investment in your home. It’s a room that you go to every day and one that is constantly being used by guests.The bathroom is one of the top trafficked rooms in a home and also one of the most valuable in terms of home resale.


    Install Piping Before Tub


    You will be using your existing drain and waste vent system, but pipes required include the hot and cold water supply lines and a pipe leading to a shower head. A mixing valve and shower head are also needed. Air chambers may be required.


    Position the Tub


    Lower the tub into place so that the continuous flange fits against the wall studs and rests on 1’x4' or 2’x4' supports. Anchor the tub to the enclosure with nails or screws inserted through the flanges into the studs.



    NOTE: Remember, bathtubs and shower stalls may require support framing. A bathtub filled with water is extremely heavy, so check building codes and framing support before installing the tub.


    Assemble Drain Connections


    Assemble the bathtub drain connections by connecting the tub overflow with the tub drain above the trap, not beyond it. The trap will have a compression fitting that screws over the arm of the overflow assembly.


    Place a Pipe For the Shower Head


    First, locate a brass female threaded winged fitting and attach it to a framing support via a screw or a nail. Then run a pipe up the wall for the shower head. Sweat or solder the other side of the brass fitting to the top of the pipe.


    Attaching Hot and Cold Water Lines


    Attach your water lines for both hot and cold by sweating these directly into the hot and cold ports of the mixing valve. The mixing valve will be how water enters the tub’s system, not by the pipes themselves.


    Install the Spout


    Extend a piece of 1/2 inch pipe, or whichever length is specified in the manufacturer’s instructions, for the tub spout. Sweat on a male threaded fitting at the end of the pipe or use a brass nipple of the proper length and a 1/2 inch cap.



    NOTE: At this point you should have your rough-in plumbing work inspected before proceeding further.


    Check For Leaks


    Restore the water pressure and check the drain connection and the supply pipes for any sign of leaking.


    estore the Bathroom Wall


    Replace the wall with moisture-resistant drywall as a base for your wall covering. Seal the joints between the wall and your new tub with silicone caulk as protection against water seepage.

    https://www.berkeys.com/2016/12/02/bathtub-installation-dallas/


    How to Install a Bathtub: Install an Acrylic Tub and Tub Surround

    As a keen person who reads on Installing A Bathtub, I was thinking sharing that piece of writing was a great idea. In case you enjoyed reading our article kindly remember to share it. Thanks for your time invested reading it.


    Leading emergency plumbing services available.

    Leave a Reply

    Your email address will not be published. Required fields are marked *